配比在2%左右時導電率為1000左右，PH值4.8-5.5之間。

When the ratio is about 2%, the conductivity is about 1000, and the PH value is between 4.8 and 5.5.

配比在3.5%左右時的導電率為1470左右，PH值4.8-5.5之間。

When the proportion is about 3.5%, the conductivity is about 1470, and the PH value is between 4.8 and 5.5.

配比在4%左右時導電率為1500左右，PH值4.8-5.5之間。

When the ratio is about 4%, the conductivity is about 1500, and the PH value is between 4.8 and 5.5.

使用情況 Usage Situation

水箱溫度應保持在10至15度，自來水的pH值影響較小，建議配比在2%-4%之間。該產品適用於所有平版印刷機品牌（如海德堡、小森、三菱等），起始配比為2.5%，若水質較硬可增加至3%-4%。包裝有25L、200L和1噸桶，並可安裝集中供水系統以自動配比，具體用量根據生產需求調整。

The temperature of the water tank should be maintained at 10 to 15 degrees, and the pH value of tap water has a small impact. It is recommended to proportionate in a ratio between 2% and 4%. This product is suitable for all sheetfed printing machine brands (such as Heidelberg, Komori, Mitsubishi, etc.), with a starting ratio of 2.5%. If the water quality is hard, it can be increased to 3% -4%. The packaging comes in 25L, 200L, and 1-ton drums, and can be equipped with a centralized water supply system for automatic proportioning. The specific amount can be adjusted according to production needs.

使用操作要求 Operation Requirements

在開印前，需根據無醇潤版液和普通潤版液的不同，調整印刷機的供水系統，包括確保上水輥平衡和適當設置計量輥壓力。首先，檢查並清洗上水輥、墨輥和橡皮布，切勿使用洗車水或汽油。調整不平衡的上水輥，避免單邊干版。調整計量輥壓力後，微調上水量。清空並徹底清洗水箱，保持溫度在10度，建議每15-20個工作日清洗一次。準確計算水箱內總水量，均勻播入潤版液後再倒入水中，補充時需按比例兌勻後再加入水箱，以免影響效果。

Before printing, it is necessary to adjust the water supply system of the printing machine according to the difference between non-alcoholic and regular fountain solutions, including ensuring the balance of the water supply roller and setting the pressure of the metering roller appropriately. Firstly, check and clean the water roller, ink roller, and rubber blanket, and do not use Ink cleaner water or gasoline. Adjust the unbalanced water roller to avoid single-sided dry plate. After adjusting the pressure of the measuring roller, fine tune the amount of water added. Empty and thoroughly clean the water tank, keeping the temperature at 10 degrees. It is recommended to clean it every 15-20 working days. Accurately calculate the total water volume in the water tank, evenly pour in the fountain solution before pouring it into the water. When replenishing, it is necessary to mix it in proportion before adding it to the water tank to avoid affecting the effect.